MOTOR MANUFACTURER · Shanghai, CHINA

Shanghai Powerful Electric Co., Ltd. (LS Powerful)

Shanghai Powerful Electric Co., Ltd. (上海六盛电机有限公司, brand LS Powerful) makes small fan motors for household appliances. Its JYF AC permanent-magnet motors and ZWF 12 V BLDC fans serve different airflow paths; below are all five catalogue models, the values each publishes and the points to confirm before ordering.

LocationShanghai, China

SHANGHAI · 上海六盛电机有限公司

Shanghai Powerful Electric (LS Powerful): JYF and ZWF fan motors

01 / COMPANY AND CATALOGUE

上海六盛电机有限公司 and the five models it publishes

Shanghai Powerful Electric Co., Ltd. (LS Powerful), Fengxian District, Shanghai

The company's own site presents LS Powerful as a developer and maker of micro motors for refrigerators, air conditioners and other household appliances: brushless DC motors, AC permanent-magnet motors and integrated BLDC fan motors. Its English catalogue currently shows five models, two JYF AC permanent-magnet motors and three ZWF 12 V BLDC units. Catalogue pages reviewed on 29 October 2026.

Two models publish no fixed operating point

JYF-02-3 (inner rotor, 2 poles and 1 slot, detachable fan, class E insulation) lists 3 W maximum power and 300 V maximum voltage; current, speed, airflow, pressure and noise all read 'according to the load'. ZWF-06-4 (inner rotor, 10 poles and 9 slots, three-phase BLDC drive, detachable fan, class E) lists 12 V rated, 15 V maximum and 4.5 W maximum, with the remaining fields also load-dependent. For either model, the fan or load you fit defines the rating; send it with the inquiry.

Supply wording differs within one JYF-02-3 page

The specification panel for JYF-02-3 gives AC115/240 V, while its rating row gives AC110–240 V. Ask whether this is one universal-voltage winding or two variants before designing for 100–110 V markets.

Approval marks are declared per page, not verified per model

The product pages show TÜV for JYF-02-3, no mark for JYF-03-2.5, and UL/TÜV for ZWF-06-4, ZWF-33-100 and ZWF-33-110-B. These are the manufacturer's labels. Ask for the certificate or file number that names the exact model and the appliance standard, and check it with the issuing body.

02 / MATCH THE FAN TO THE AIR PATH

Axial, centrifugal and detachable-blade designs do different jobs

AC permanent magnet: start with the appliance supply

The manufacturer's JYF-02-3 is an inner-rotor AC permanent-magnet motor shown with a detachable fan, while JYF-03-2.5 is an outer-rotor axial-fan design. The JYF-03-2.5 table gives AC100–240 V, 0.08 A, 3 W maximum, 1,650 rpm ±10%, 3.40 cubic metres per minute and 36 Pa. Those are one catalogue entry's stated values, not a guarantee at a buyer's duct pressure or a rating for JYF-02-3, whose airflow and speed fields say they depend on the load.

Confirm before ordering Send mains voltage/frequency, available space, fan diameter, duct impedance, target airflow at static pressure, thermal ambient and electrical isolation requirements. Ask for the exact JYF impeller and connector, measured operating curve in the appliance and a current-revision safety file.

BLDC axial: airflow through a short path

ZWF-33-110-B is listed as a 12 V outer-rotor axial fan with PWM or voltage speed control and tachometer output. Its row states 0.2 A, 2 W maximum, 2,300 rpm ±150, 2.10 cubic metres per minute and 45 Pa. At 12 V, 0.2 A implies 2.4 W input, so the current and stated maximum-power fields need reconciliation; do not treat them as a verified common operating point. Neighbouring ZWF-33-110-D/E pages are separate variants. A restrictive grille can change delivered volume sharply.

Confirm before ordering Define inlet and outlet geometry, system resistance, minimum voltage at the fan, PWM frequency and logic levels, tach pulses/connector pinout, acoustic limit, orientation and fault response. Ask for a corrected electrical rating, a flow-versus-pressure curve and a sample tested behind the actual grille.

BLDC centrifugal: pressure and scroll geometry matter

ZWF-33-100 is a separate inner-rotor centrifugal design, also listed for 12 V PWM/voltage control with tach feedback. Its row states 0.104 A, 2 W maximum, 1,950 rpm ±10%, 1.00 cubic metre per minute and 45 Pa. The same 45 Pa figure as the axial entry does not make the two interchangeable: their housings, flow paths and resulting fan curves must match the machine.

Confirm before ordering Provide scroll or duct drawing, outlet orientation, back-pressure range, mounting bosses, wiring clearance and continuous duty. Compare both candidates on the same installed system curve rather than on a single headline air-pressure value.

03 / KEEP MODEL AND APPROVAL SCOPE SEPARATE

The electrical interface is part of the fan specification

The catalogue names different motor architectures

The JYF pages describe AC permanent-magnet motors; the ZWF pages describe DC brushless fan assemblies with PWM/VCC speed input and tach signal. An AC replacement and a 12 V BLDC fan cannot share the same driver or safety wiring simply because both move air. Even within the ZWF range, axial and centrifugal housings differ.

Original third-party records establish a narrow, historic example

UL Product iQ lists Shanghai Powerful Electric as a file holder. A 2022 refrigerator safety descriptive report names the firm's ZWF-32-120 and ZWF-30-3 as 12 V, 2.5 W evaporator-fan components in that appliance file. This is evidence of specific historic component use, not a certificate for the presently listed ZWF-33-110-B or every LS Powerful fan. The manufacturer's own UL/TUV field on product pages still needs a current model-specific record.

A rating row is not the installed operating point

The published fan rows each show one airflow and one pressure value without a complete flow-versus-pressure curve or stated test fixture. The ZWF-33-110-B electrical row also needs clarification because its current and maximum-power figures do not align at the stated 12 V. In an actual cabinet, filter, duct, evaporator or medical-device housing, pressure loss and noise can change sharply. Request corrected data and a repeatable installed-system test before approving a substitute.

04 / MAKE THE COMPARISON MEASURABLE

Send a duct drawing and controller pinout, not just a fan diameter

For a new refrigeration or equipment enclosure

Specify supply tolerance, duct/grille/filter or evaporator resistance, airflow at that resistance, ambient and condensation exposure, continuous run time, allowable vibration/noise, mounting and cable clearance. Request the complete fan assembly code, curve, connector/pinout, PWM and tach behaviour, locked-rotor response, acoustic method and an instrumented sample in the finished enclosure.

For a replacement supplier

Provide the incumbent fan label, measured system curve, interface drawing, startup and low-voltage data, current and noise at the operating point, and applicable product safety file. Ask for a side-by-side endurance and thermal check in the same appliance. A model from the same maker's older refrigerator report does not automatically validate a different ZWF variant.

Company information

Company name
Shanghai Powerful Electric Co., Ltd. (LS Powerful)
Chinese registered name
上海六盛电机有限公司
Region
Shanghai, China
Record updated
2026-10-29

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail