YZO vibration motor

Manufacturer catalogue image · Series illustration

Application-specific motors

YZO vibration motor

Power
0.09–40 kW
Voltage
380 V
Mounting
Horizontal
Frequency
50 Hz

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

Navigate Shanghai Shangzhen’s YZO catalogue by vibration frequency

This horizontal-vibrator catalogue covers four pole groups for feeders, screens, conveyors and other vibrating equipment. Choose the machine’s intended vibration frequency first, then compare complete model rows. The largest 700 kN entry belongs to the six-pole group; it does not describe the whole family.

Four catalogue groups, four operating frequencies

All four tables are headed 380 V and 50 Hz. Their listed vibration counts are catalogue operating values, not the exact synchronous speeds inferred from the pole count.

Pole groupCatalogue vibration countWhere to start an existing-machine inquiry
Two-pole 2900 per minute Existing full model and the two-pole table
Four-pole 1430 per minute Existing full model and the four-pole table
Six-pole 970 per minute Existing full model and the six-pole table
Eight-pole 720 per minute Existing full model and the eight-pole table

At 150 kN, carry the drawing reference through to the order

These four six-pole entries each list 10.00 kW, 22.89 A and eight M36 fasteners. The remaining differences below make the suffix part of the mechanical specification. Dimensions are mm and drawing numbers refer to this manufacturer’s table.

ModelA / BLMassDrawing no.
YZO-150-6 520 / 118 890 660 kg 4
YZO-150-6C 460 / 118 890 635 kg 4
YZO-150-6FB 460 / 118 940 695 kg 5
YZO-150-6A 540 / 340 940 700 kg 6

Two catalogue traps to resolve before a purchase order

The table is useful for shortlisting. The final offer still needs one complete model and its supplied configuration.

The 700 kN headlineYZO-700-6A is a specific six-pole assembly: 40 kW, 86.39 A, 2755 kg and sixteen M42 fasteners. Its A/B dimensions are 750/500 mm. A machine support or handling plan for a smaller YZO motor cannot be assumed adequate for this entry.
IP55–IP66 and F or HThe introduction presents a protection range and alternative insulation classes, not one combined standard specification. Put the required enclosure and insulation into the inquiry and ask the offer to identify the supplied version. The same applies to a special voltage or frequency.

Attach the machine requirement to the selected row

A useful request identifies the full suffix, pole group and intended installation, so the quotation does not stop at a force rating.

Replacing a 150-6 variant

Attach the nameplate, its current drawing number, measured mounting pattern and available length. Use the four-row comparison to flag the exact discrepancy; ask the supplier to resolve it before authorising base-plate work.

Specifying a new vibrating assembly

Provide the equipment designer’s force and vibration-frequency requirement, moving mass, material load, motor positions and duty. Ask for approval of the support and exciter arrangement. The catalogue alone cannot predict material travel or throughput.

CATALOGUE OVERVIEW

About this motor series

Shangzhen’s YZO range uses a horizontal mounting arrangement for feeders, screens, conveyors and compaction equipment. The published tables span 0.09–40 kW and include two-, four-, six- and eight-pole groups. The YZO-700-6A entry is a 40 kW, 700 kN, 970 rpm configuration weighing 2755 kg; these figures belong to that large variant, not every YZO motor. Smaller entries have different bolt patterns and structural loads.

Model / series reference: YZO

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.09–40 kW
Voltage
380 V
Mounting
Horizontal
Frequency
50 Hz
Product Type
YZO vibration motor
Speed Groups
2900 / 1430 / 970 / 720 rpm
Catalogue Scope
Manufacturer model or series
Tabulated Output
0.09–40 kW
Largest Listed Excitation Force
700 kN
Speed
Model dependent
Manufacturer
Shanghai Shangzhen

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail