MOTOR MANUFACTURER · Shanghai, CHINA

Shanghai Crane Motor Factory Co., Ltd.

The load cycle decides the motor. Shanghai Crane Motor Factory distinguishes YZR wound-rotor cranes, YZ cage-rotor cranes, YZB inverter cranes and YSG mill rollers. Match starting, braking and thermal duty before comparing frame size.

LocationShanghai, China

SHANGHAI · CRANE AND METALLURGICAL DRIVES

Shanghai Crane Motor Factory: choose rotor, brake and duty for a crane or mill roller

01 / WHAT THE MACHINE ACTUALLY DOES

A hoist, a travelling crane and a work roller do not share one motor answer

YZR: retain or redesign the wound-rotor circuit

The manufacturer's YZR/YZ sheet explicitly calls YZR wound-rotor and YZ squirrel-cage. Its YZR II page describes an external resistor in the rotor circuit to limit starting current. For an existing crane, that makes slip rings, brush maintenance, resistor stages and contactor sequencing part of the replacement design, not optional accessories hidden by a common frame height.

Confirm before ordering Provide the old rotor terminal and resistor schematic, full hoist load cycle, starts per hour, braking and reversal pattern, supply, shaft/coupling and available cooling. Ask for the exact rotor open-circuit data and starting/thermal calculation for the offered YZR frame.

YZ: check cage starting against the supply and load

The YZ family is the cage-rotor branch. Its YZ II sheet describes direct-on-line starting under specified 380V/50Hz conditions and separate S3-15%, S3-25% and S3-40% output columns. A duty-column change alters the applicable output for the same frame, so quoting only a frame or a maximum table value is insufficient.

Confirm before ordering State short-circuit capacity, allowable starting current, mechanical acceleration, S3 duty or other operating cycle, ambient, mounting and protection. Require a particular duty-column and starting-torque row, plus a brake interface for any suspended load.

YZB: inverter control still needs a crane system design

The separate YZB page describes an inverter-duty crane and metallurgical induction motor for frequent starting, braking and reversal. It does not make every published variant suitable for every low-speed lifting duty. Confirm the VFD's torque limits, external ventilation, encoder option, brake sequence and emergency-stop architecture with the actual ordered frame.

Confirm before ordering Send maximum/minimum load, hoist speed band, acceleration and regeneration schedule, VFD model, feedback need and ambient. Request a motor-drive operating map and who is responsible for mechanical holding, overspeed and commissioning.

YSG: separate reversing work rollers from continuous transfer rollers

The factory's YSG roller-table sheet divides YSGa, a softer-characteristic type for frequent work-roller starts/reversals, from YSGb, a harder-characteristic type primarily described for S1 transfer rollers. The page describes different frequency ranges for these use cases. Choosing from the family name alone risks the wrong torque and heating behaviour on a steel line.

Confirm before ordering Provide roller diameter, line speed, impact and jam loads, material temperature, reversal count, drive ratio and VFD. Ask for the exact YSGa or YSGb duty, bearing/seal arrangement, lubrication plan and test points at the slowest loaded speed.

02 / BEYOND THE MOTOR NAMEPLATE

Holding a suspended load is a system requirement

Starting, braking and holding are different duties

A rotor-resistor circuit, inverter electrical braking and mechanical holding brake act at different points in the motion sequence. Identify the independent holding device, its supply and release interlock, stopping energy and fault response. A crane motor's overload description or an S3 table does not by itself certify a lifting assembly.

Environmental labels need a specific configuration

The YZ II sheet distinguishes IP54 motor housing from IP55 terminal box, while the YZR II page gives insulation-dependent ambient limits. For hot, dusty steelmaking or outdoor ports, request the exact ordered enclosure, insulation, cooling, cable-entry and bearing arrangement instead of lifting the broadest claim from another family.

03 / A REAL RFQ PACKAGE

Put cycle data and responsibility boundaries on one page

What should the buyer send?

Include crane mechanism or roller location, rated and peak loads, reflected inertia, speeds, start/brake/reverse counts, S3/S5/S1 timeline, supply/VFD/rotor circuit, site temperature and contamination, mounting/shaft drawing, brake and encoder interfaces, and required standards at the destination.

What should the supplier return?

Request the exact series, frame and winding, duty-column power/torque and thermal curves, starting or inverter/rotor circuit diagram, cooling and protection, brake and feedback options, outline drawing, routine test plan and site commissioning responsibility. Keep motor factory tests distinct from full crane or mill-line acceptance.

04 / SOURCE INTERPRETATION

Read each published table in its own machine context

The YZR/YZ distinction is explicit despite the company overview

The website overview loosely groups both families together as wound-rotor; its detailed YZR/YZ sheet correctly identifies YZR as wound-rotor and YZ as cage-rotor. This page follows the product sheet and flags the distinction because a rotor-resistor starter cannot be transferred to a cage motor.

Neither a historic standard phrase nor a client list is a model certificate

The YZB and YSG pages contain standards and application language, and the company describes steelworks customers. These are useful for selecting questions but do not certify a particular current unit or establish delivery history for this buyer. Obtain the exact order drawing, current test records and project-specific conformity documents.

Company information

Company name
Shanghai Crane Motor Factory Co., Ltd.
Chinese registered name
上海起重电机厂有限公司
Region
Shanghai, China
Record updated
2026-10-07

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail