W.E1041R / W.E2041R door-opener motor

Manufacturer catalogue image · Series illustration

Application-specific motors

W.E1041R / W.E2041R door-opener motor

Voltage
12 / 24 V
Loaded Speed
40 rpm ±5%
Product Type
W.E1041R / W.E2041R door-opener motor
No-load Speed
50 rpm ±10%

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

W.E1041R / W.E2041R: size the door movement from 7 N·m, not the brake or gear-strength figure

Baixiang publishes this door-opener motor pair with 12 V and 24 V supply options and a common 7 N·m working-torque entry. The product photograph identifies a W.E2041R unit as DC 24 V, 7 N·m. For a replacement, start with the existing door linkage, loaded speed and controller supply; the larger braking and gear-strength figures describe different limits.

Three torque figures answer three different questions

7 N·m: the working pointThis is the published working torque for both voltage columns, paired with 40 rpm ±5% loaded speed. It is the relevant starting point for matching normal door movement. The page does not state a continuous-duty duration or cycles-per-hour rating, so the actual opening/closing cycle still needs confirmation.
At least 24 N·m: braking torqueThe detailed table specifies ≥24 N·m; the short introduction uses >24 N·m. Use the detailed table’s stated lower bound rather than presenting an exact brake setting. This is not 24 N·m of available driving torque, nor does the page establish an emergency-stop or person-protection function.
At least 30 N·m: gear strengthThe table lists ≥30 N·m under gear strength. It does not provide a duration or repetitive-load qualification for that figure. Do not size the moving door at 30 N·m or treat the value as an allowable recurring overload. A jam or hard-stop condition needs its own protection strategy.

The voltage option changes the current requirement

Both columns share the published speed and working torque. These are the manufacturer’s stated operating entries, not measured starting or stalled-current values. Confirm the full nameplate and winding with the delivered unit; the photo specifically shows the 24 V W.E2041R.

SupplyNo-load currentLoad currentLoaded speed
12 V DC 2.5 A ≤8 A 40 rpm ±5%
24 V DC 1.5 A ≤5 A 40 rpm ±5%

Make the replacement inquiry describe one complete door movement

Use loaded speed when comparing opening time

The no-load entry is 50 rpm ±10%, or 45–55 rpm. The loaded entry is 40 rpm ±5%, or 38–42 rpm. Those are shaft speeds, not door travel speed: opening time also depends on the linkage ratio and geometry. Send the required travel, available opening time and existing reduction or crank arrangement rather than asking for “50 rpm” from the unloaded figure.

Confirm rotation from a defined viewing side

The page describes red positive for clockwise rotation and green positive for counterclockwise rotation, but does not specify the viewing side. Include the required output rotation as seen from the mechanism connection and obtain the wiring instruction for that assembly. The R suffix alone should not be used to decide the installed opening direction.

Match the output and cycle before ordering

The photo shows a geared output housing, fixing points and a projecting shaft, but the page provides no usable dimensioned installation drawing. Supply the old motor’s fixing-hole measurements, output-interface details, cable clearance and door cycle, including dwell and reversal. The stated −20 to +60°C range and ≤55 dB(A) noise figure do not establish enclosure protection or an installed acoustic result; ask for the enclosure rating and noise test condition if those are purchase requirements.

CATALOGUE OVERVIEW

About this motor series

Baixiang’s W.E1041R/W.E2041R door-opener motor has 12 V and 24 V options. Both list 7 Nm working torque, 40 rpm loaded speed with ±5% tolerance, and 50 rpm no-load speed with ±10% tolerance. Maximum load current differs: 8 A for 12 V and 5 A for 24 V. The table gives at least 24 Nm braking torque, at least 30 Nm gear strength and an operating temperature range of −20 to +60 °C.

No continuous shaft-output rating is stated. Electrical current is not converted into rated mechanical output.

Model / series reference: W

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Voltage
12 / 24 V
Loaded Speed
40 rpm ±5%
Product Type
W.E1041R / W.E2041R door-opener motor
No-load Speed
50 rpm ±10%
Braking Torque
≥24 Nm
Working Torque
7 Nm
Catalogue Scope
Manufacturer model or series
12 V Load Current
≤8 A
24 V Load Current
≤5 A
Operating Temperature
−20 to +60 °C
Power
Confirm configuration
Speed
Model dependent
Manufacturer
Baixiang Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail