Horizontal cast-iron oil-pump motor

Manufacturer catalogue image · Series illustration

Application-specific motors

Horizontal cast-iron oil-pump motor

Phase
Three-phase
Frame Range
80–160L
Construction
Horizontal cast-iron housing
Pole Options
4 / 6

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

An iron-housing pump motor can share a centre height and still miss the base

For this horizontal pump-motor range, the S, M and L frame suffixes affect the installed envelope. A replacement check needs the foot spacing, pump-end projection and available length together; centre height alone is not a fit check.

Four outlines worth distinguishing before ordering

Dimensions below are in millimetres, transcribed from the horizontal cast-iron sheet. A and B are the transverse and longitudinal foot-hole spacings; C is the reference distance shown from the front foot line toward the pump end. All four rows use drawing 2.

FrameA × BH centre heightC referenceL overall lengthK fixing hole
112S 190 × 140 112 58 314 12
112L 190 × 140 112 74 346 12
160M 254 × 210 160 92 485 15
160L 254 × 254 160 83 530 15

Which measurement changes your replacement plan?

112S to 112L: the same holes do not mean the same envelope

The listed A × B spacing and centre height are identical, but overall length increases by 32 mm and C increases by 16 mm. Check where the pump face sits relative to the fixed pipework and whether the fan-cover end has room. Those two changes are not a single adaptor thickness.

160M to 160L: the base also changes

Longitudinal hole spacing B grows from 210 to 254 mm, while overall length grows from 485 to 530 mm. The reference dimension C decreases from 92 to 83 mm. A longer frame therefore cannot be positioned simply by adding the length difference at the rear; compare both foot rows and the pump-side datum.

Small frames use another outline

Frames 80 and 90S are assigned drawing 1, whereas frame 100 and the four rows above use drawing 2. Use the actual drawing number when asking for the mating interface. The common cast-iron description does not establish a shared pump register or bolt circle.

Approve the motor and pump as a connected assembly

Resolve the front connection before machining a base

The outline sheet does not provide a complete dimensioned pump register, fixing pattern and drive engagement. Send the existing pump drawing, photographs of the mating face and the rotation requirement with its viewing direction. Ask for an approved motor-to-pump assembly drawing that locates the feet against that interface.

Choose poles from the pump speed requirement

The sheet separates four- and six-pole entries, but does not supply rated speed, current or torque curves for each winding. Specify the pump’s required operating speed, supply frequency, pressure and flow, plus the existing nameplate. Do not assume that selecting the same frame preserves hydraulic output.

Obtain an unambiguous electrical rating

The power heading combines kW and horsepower wording with fractional entries. The dimensions can support a layout check, but the accepted quotation should separately state rated kW, voltage, frequency, current and duty for the selected winding. No conversion of the mixed-heading entries is used on this page.

CATALOGUE OVERVIEW

About this motor series

Baote’s horizontal cast-iron oil-pump motor drawing table covers frames 80–160L and separates four- and six-pole configurations. It also uses two different outline drawings, with overall lengths from 255 to 530 mm across the listed rows. The pump-side connection and foot dimensions must match the actual assembly. The source labels fractional power entries with both horsepower wording and kW, so a reliable kW range cannot be assigned from this sheet alone.

Source power units are inconsistent; no HP-to-kW conversion is applied without a confirmed nameplate.

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Phase
Three-phase
Frame Range
80–160L
Construction
Horizontal cast-iron housing
Pole Options
4 / 6
Product Type
Horizontal cast-iron oil-pump motor
Catalogue Scope
Product family / configuration confirmed on inquiry
Listed Overall Lengths
255–530 mm
Power
Confirm configuration
Voltage
Confirm supply
Speed
Model dependent
Manufacturer
Baote Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail