YSE soft-start brake motor

Manufacturer catalogue image · Series illustration

Brake motors

YSE soft-start brake motor

Voltage
380 V
Duty
S3 40%
Frequency
50 Hz
Insulation
Class F

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

Choose crane-travel speed and braking before matching 2.2 kW

The first-generation Huyuan YSE/R1 combines a solid-rotor induction motor with an AC brake. Its deliberately high-slip characteristic is part of the travel drive: a motor with the same kilowatt label but a different pole group can change travel speed, starting behaviour and the available brake-torque range.

Three 2.2 kW entries are not interchangeable

These rows are within the introductory 80–160 frame range. Rated speeds come from the table’s merged pole-group cells, not the adjacent synchronous-speed column. Locked-rotor current is a starting/stall value, not rated running current.

YSE table modelRated speedLocked-rotor torqueLocked-rotor currentBrake-torque range
100L1-4 1200 rpm 24 N·m 10 A 2–10 N·m
112M-6 800 rpm 46 N·m 16 A 3–30 N·m
112S-8 600 rpm 48 N·m 14.8 A 3–30 N·m

What changes when the motor is fitted to the crane

Travel speed follows rated speed and the transmission

At unchanged gearing and wheel diameter, the listed 800 rpm entry gives two-thirds of the 1200 rpm entry’s shaft-speed basis; the 600 rpm entry gives half. This is a transmission-ratio comparison, not a prediction of actual loaded crane speed. The synchronous figures are 1500, 1000 and 750 rpm for these three groups. Substituting them for the listed rated speeds overstates each by 25%, so use the actual rating and load-speed behaviour when checking travel requirements.

Mechanical soft starting is not an electronic ramp setting

Huyuan attributes the effect to the solid rotor’s high slip and soft mechanical characteristic. The page does not specify a programmable acceleration time. Provide the moving mass, wheel diameter, gearbox ratio, travel resistance and required acceleration; have the offered motor checked against that load. A same-power general-purpose motor or an electronic soft starter alone does not establish equivalent travel behaviour.

Brake adjustment is part of the machine stopping calculation

The 100L1-4 range tops out at 10 N·m, whereas the two 112-frame examples list up to 30 N·m. Those are motor-side brake figures, not a guaranteed crane stopping distance or permission to use the maximum setting. Give the load inertia, speed, required stop distance, transmission ratio and starts/stops per hour so the brake energy and setting can be selected together. The page’s 0.08-second response headline is not a whole-machine stopping-time guarantee.

Agree the duty and brake circuit for the supplied generation

The R1 specification table states 380 V, 50 Hz, S3 40%, IP54 and class F, and the brake is identified as 380 V AC. Preserve that intermittent-duty designation in the order; marketing claims about long running or surviving a stall do not establish an S1 rating, an allowed stall test or a protective-device setting. Include the real jogging and start/stop cycle, brake release/control scheme and required protection in the technical agreement. Larger rows beyond the introductory frame range need their own generation-specific confirmation.

CATALOGUE OVERVIEW

About this motor series

Huyuan’s first-generation YSE soft-start brake motor uses a solid rotor and AC brake for crane travel. Its general specification gives 380 V, 50 Hz, S3 40% duty, IP54 and class F insulation. The 90S-4 example is 1.1 kW with a listed 1200 rpm rated speed; synchronous speed is separately shown as 1500 rpm. The introduction and extended rating table cover different frame/power limits, so they should not be combined into one unqualified range.

The overview lists frames 80–160 and 0.4–15 kW, while the extended table includes larger sizes. Confirm which table applies to the supplied generation.

Model / series reference: YSE

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Voltage
380 V
Duty
S3 40%
Frequency
50 Hz
Insulation
Class F
Protection
IP54
Product Type
YSE soft-start brake motor
Example Model
90S-4: 1.1 kW; 1200 rpm rated
Catalogue Scope
Manufacturer model or series
Reviewed Variant
First-generation YSE / R1
Power
Confirm configuration
Speed
Model dependent
Manufacturer
Huyuan Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail