Machine-tool spindle motor range

Manufacturer catalogue image · Series illustration

Application-specific motors

Machine-tool spindle motor range

Application
Machine-tool spindle drive
Product Type
Machine-tool spindle motor range
Catalogue Scope
Product family / configuration confirmed on inquiry
Catalogue Families
165Y / 180H / 204Y / 204YJ / 265Y

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

Choose the spindle family by its usable power–speed region

Mige’s 204Y and 204YJ can carry the same nominal power and maximum-speed figure while offering different constant-power limits. The 180H family uses another base speed and distinguishes continuous power from a 30-minute rating. Start with the machining speed and duty, then match the drive feedback and installation drawing.

Two 5.5 kW spindle motors with different high-speed capability

The 204Y page identifies the 00B000 model; the 204YJ page identifies 00B001. The maximum speed alone hides the difference in constant-power range.

Catalogue characteristicMY204-350CGDI4-00B000 (204Y)MY204-350CGDI4-00B001 (204YJ)
Rated power / torque 5.5 kW / 35 Nm 5.5 kW / 35 Nm
Rated speed / frequency 1,500 rpm / 51.5 Hz 1,500 rpm / 51.5 Hz
Constant-power maximum speed 6,000 rpm 3,600 rpm
Maximum speed 8,000 rpm 8,000 rpm
Rated current 13.0 A 13.5 A
Catalogue inertia 0.0210 kg·m² 0.0186 kg·m²
Overall length L 511 mm 486 mm
Mass 43.6 kg 38.7 kg

A maximum-speed figure does not promise full power at that speed

For machining above 3,600 rpm, check the 204YJ curve

The 204YJ table stops its constant-power region at 3,600 rpm, whereas the 204Y table extends it to 6,000 rpm. Both list 8,000 rpm maximum. A process requiring the full 5.5 kW at 5,000 rpm cannot be selected from the common 8,000 rpm headline; the shorter 204YJ has a different published power envelope. The 204YJ graphic contains inconsistent torque-axis speed markings, so use a confirmed selected-model curve rather than inferring intermediate torque from that graphic.

180H uses S2-30 min, not an unlimited higher rating

MH180-117FGDR1-02A200 is listed at 3.7 kW, 11.7 Nm, 3,000 rpm and 280 V. Its curves distinguish 3.7 kW S1 from 5.5 kW S2-30 min. The short-time curve is not a 5.5 kW continuous rating. Its maximum-speed cell shows 12,000/15,000 rpm, while the plotted power curve only reaches 12,000 rpm; obtain the exact speed option and allowable duty for the selected configuration.

The larger 265Y family does not inherit the 180H speed range

The 265Y table covers rated outputs from 11 to 30 kW at 1,500 rpm, with a listed constant-power limit of 6,000 rpm and maximum speed of 8,000 rpm. These are different selection boundaries from 180H. Choose the family from required cutting power over speed and the machine acceleration demand, not by combining the largest power from one family with the highest speed of another.

Finish the selection with the actual feedback and shaft option

204-family feedback choicesThe 204Y and 204YJ performance sheets list optional I1 1000 incremental, I2 2500 incremental, R2 resolver and A1 17-bit absolute feedback. They also distinguish plain and keyed shafts. Match the selected feedback type to the spindle drive’s supported interface and commissioning data; a 17-bit label alone does not identify the protocol or connector pinout.
The 25 mm length saving changes the mounting checkThe 5.5 kW 204YJ outline is 486 mm long versus 511 mm for 204Y. Its L1 entry is 128 mm, while the 204Y sheet lists 128/153 mm alternatives. Both drawings show 38 mm shaft diameter and an 80 mm projection. Verify the exact feet, shaft option and guard clearance from the ordered drawing rather than treating a shared 204-family name as proof of a drop-in fit.
180H has different protection and mounting dataThe 180H performance sheet lists B35 mounting, a plain shaft and IP54 protection; the 204Y/204YJ sheets list B3, B35 or B5 and IP55. Keep those choices with the selected family. Resolver or incremental feedback options for 180H must likewise be confirmed on that family’s sheet rather than copied from the 204 alternatives.

CATALOGUE OVERVIEW

About this motor series

Mige’s spindle-motor catalogue lists 165Y, 180H, 204Y, 204YJ and 265Y families. The listing distinguishes these spindle products from its servo and stepper sections, but it does not establish a common rating across the five families. For machine-tool integration, request the selected model’s base speed, constant-power region, feedback interface and mechanical drawing.

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Application
Machine-tool spindle drive
Product Type
Machine-tool spindle motor range
Catalogue Scope
Product family / configuration confirmed on inquiry
Catalogue Families
165Y / 180H / 204Y / 204YJ / 265Y
Power
Confirm configuration
Voltage
Confirm supply
Speed
Model dependent
Manufacturer
Mige Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail