BB36 5–15 W brushless DC motor family

Manufacturer catalogue image · Series illustration

DC motors

BB36 5–15 W brushless DC motor family

Power
0.005–0.015 kW
Voltage
12 or 24 V DC
Mass
220 / 240 / 255 g by output
Feedback
Hall / no-Hall options listed; confirm ordered version

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

BB36: choose the torque first, then match the 12 or 24 V winding

The BB36 has three output levels at the same 3,000 rpm rated speed. Moving from 5 W to 15 W triples the listed torque but adds 20 mm of body length. Choosing 24 V instead of 12 V changes the rated current within each output pair; it does not raise that pair’s torque.

Six catalogue rows, three mechanical output choices

All rows list 3,000 rpm rated speed and 3,700 rpm no-load speed. Dimensions and mass below are the catalogue entries, before resolving the separate driver-cover allowance.

Exact modelSupplyOutput / torqueRated currentLength / mass
BB36530S12 12 V 5 W / 0.016 Nm 0.64 A 45 mm / 220 g
BB36530S24 24 V 5 W / 0.016 Nm 0.32 A 45 mm / 220 g
BB361030S12 12 V 10 W / 0.032 Nm 1.28 A 55 mm / 240 g
BB361030S24 24 V 10 W / 0.032 Nm 0.64 A 55 mm / 240 g
BB361530S12 12 V 15 W / 0.048 Nm 1.92 A 65 mm / 255 g
BB361530S24 24 V 15 W / 0.048 Nm 0.96 A 65 mm / 255 g

What changes when a 5 W unit is replaced by a 15 W unit?

Supply wiring must follow the output as well as the voltage

At 24 V, the listed rated current rises from 0.32 A to 0.96 A; at 12 V it rises from 0.64 A to 1.92 A. These are rated operating currents, not startup or jam-current limits. Specify the acceleration, load cycle and required current limiting with the drive. Reusing a supply only because its voltage matches does not establish that it can run the larger winding.

The common front interface does not make the rear envelope identical

The outline shows a 36 ±0.1 mm body and four M3 mounting holes on a 25 ±0.2 mm circle. The length column grows from 45 to 65 mm across the output choices, and mass from 220 to 255 g. Check the actual support, screw depth and cable exit against the selected assembly drawing before treating the larger motor as a drop-in replacement.

Resolve the 17 mm rear cover explicitly

All six rows mark internal drive “Yes” and list “17 mm (Back Cover Type)” under internal-driver length. The page does not clearly state whether the L dimension includes this section. Ask for the complete assembly length on the order drawing rather than automatically adding 17 mm to the table or assuming it is already included. Hall/no-Hall and control arrangements are customizable, so the supply and signal pin assignment must also match the ordered version.

Use 3,000 rpm as a rated point, not a promise at every load

Do not apply the unlabelled curve to all six windings

The characteristic plot shows speed falling as torque rises, but does not identify an exact model suffix. Its plotted voltage scale is also not a statement of a fixed 12 or 24 V condition for every row. It cannot establish a shared peak efficiency, maximum continuous torque or stall limit for the whole family. Use the selected winding’s confirmed curve when the application depends on an intermediate working point.

State the shaft requirement in the inquiry

Give the required torque at operating speed, starts per hour and duration of each loaded run, then identify the exact BB36 suffix and available installation length. If the load requires a different speed or shaft, request that configuration’s drawing and performance data: a customizable option is not evidence that the standard torque and dimensions remain unchanged.

CATALOGUE OVERVIEW

About this motor series

The BLDC BB36 series provides six listed combinations: 5, 10 or 15 W output, each available at 12 or 24 V DC. All are shown at a 3000 rpm rated speed, with torque rising from 0.016 to 0.048 Nm across the three output levels. Their body lengths are 45, 55 and 65 mm, and the corresponding catalogue masses are 220, 240 and 255 g. These model-dependent dimensions matter when upgrading an existing compact drive. The manufacturer lists Hall/no-Hall customization and an internal-driver arrangement with a 17 mm rear cover. Before ordering, confirm whether that cover is included in the overall installation length, identify the required control interface and request the current-versus-load data for the exact voltage and output combination.

Model / series reference: BB36

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.005–0.015 kW
Voltage
12 or 24 V DC
Mass
220 / 240 / 255 g by output
Feedback
Hall / no-Hall options listed; confirm ordered version
Body Length
45 / 55 / 65 mm by output
Rated Speed
3000 rpm
Rated Torque
0.016 / 0.032 / 0.048 Nm by output
Internal Driver
Listed with 17 mm rear cover
Rated Output Options
5, 10 or 15 W
Speed
Model dependent

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail