YE3 three-phase induction motor

Manufacturer catalogue image · Series illustration

AC induction motors

YE3 three-phase induction motor

Power
0.55–315 kW
Voltage
380 V
Duty
S1
Cooling
IC411

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

Shiyang YE3: identify the flange and mounting direction before a replacement

A YE3 frame number does not specify the mating flange. The catalogue includes both through-hole FF and threaded-hole FT arrangements, while vertical mounting availability changes with frame size. Match the machine interface first, then attach the exact electrical row.

Frame 100L: the same shaft can arrive with a very different flange

The two no-foot drawings list the same 28 mm shaft, 60 mm shaft extension, 8 mm key width and 435 mm length for frame 100L. Their flange connections differ as follows; all dimensions are millimetres.

Mating featureFF215 through-hole flangeFT130 threaded-hole flange
Fixing-circle diameter M 215 130
Locating diameter N 180 110
Outside flange diameter P 250 160
Four fixing holes S 14.5 through-holes M8 threaded holes
Locating projection T 4 3.5

Choose an installation drawing, not just “flange mounted”

Specify which side accepts the fastener

The FT drawing has threaded holes in the motor flange; the FF drawing has clearance holes. Check the machine-side fastener access, pilot fit and available space. A 100L shaft and power match cannot compensate for the 85 mm difference between these two fixing-circle diameters.

Vertical orientation depends on frame size

The mounting chart lists V1 and V3 for frames 80–160, but lists V1 only in those columns for frames 180–280 and 315–355. V1 is the shaft-down flange arrangement; V3 is shaft-up. For a larger shaft-up installation, obtain an explicitly approved arrangement rather than rotating a horizontal unit and assuming the catalogue covers it.

Large vertical units have their own envelope

The separate shaft-down vertical drawing lists frame 180L with 850 mm length, while the horizontal no-foot FF300 table lists 790 mm. Both show a 48 mm shaft with 110 mm extension. That 60 mm envelope difference matters even though the shaft and flange interface match. Use the vertical drawing for enclosure clearance and coupling alignment.

Close the order with the 100L winding suffix

100L1-4: 2.2 kWThe four-pole table lists 4.76 A, 1,440 rpm and 86.7% efficiency at 380 V, 50 Hz. This is the L1 electrical row, not a rating for every frame-100 motor.
100L2-4: 3 kWThe L2 row lists 6.34 A, 1,440 rpm and 87.7% efficiency at the same supply. Record the full winding designation plus the agreed flange and orientation on one order. The shared frame-100L dimensional table does not remove the need to match the load and electrical rating.

CATALOGUE OVERVIEW

About this motor series

Shiyang’s YE3 brochure gives a 0.55–315 kW family in 80–355 mm frames. Standard conditions are 380 V, 50 Hz, S1 duty and ambient air from −15 to +40 °C. IP55 protection and IC411 cooling are specified. Separate two-, four- and six-pole tables provide current, efficiency and shaft speed; use the selected row, since synchronous speed is not the rated shaft speed.

Model / series reference: YE3

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.55–315 kW
Voltage
380 V
Duty
S1
Cooling
IC411
Mounting
B3 / B5 / B35
Protection
IP55
Frame Height
80–355 mm
Product Type
YE3 three-phase induction motor
Catalogue Scope
Manufacturer model or series
Insulation / Temperature Rise
F / B
Speed
Model dependent
Manufacturer
Shiyang Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail