YY capacitor-run single-phase induction motor

Manufacturer catalogue image · Series illustration

AC induction motors

YY capacitor-run single-phase induction motor

Power
0.025–2.2 kW
Voltage
110 / 220 V
Product Type
IEC single-phase induction motor
Example YY90L2
2.2 kW; 2800 rpm at 50 Hz

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

Choose the YY winding for the machine speed and the load it must start

The 1.5 kW YY90S2 and YY90L4 entries show why power alone is insufficient for a capacitor-run replacement. The four-pole motor turns at half the two-pole speed at the listed 50 Hz condition, while both have a starting-torque ratio of only 0.3. Work from required shaft speed and breakaway load, then confirm the capacitor and winding.

Two 1.5 kW choices perform different jobs

YY90S2: faster shaft, lower torque at the same outputThe table lists 2800 rpm at 50 Hz and 3380 rpm at 60 Hz, with 19/9.5 A for the 110/220 V voltage pair. Using 1.5 kW and the listed 50 Hz speed gives approximately 5.12 N·m of rated shaft torque. This is calculated from T = 9550P/n, not a measured torque curve.
YY90L4: slower shaft, roughly twice the 50 Hz torqueThis 1.5 kW entry lists 1400 rpm at 50 Hz, 1700 rpm at 60 Hz and 19.8/9.9 A at 110/220 V. The same calculation gives approximately 10.23 N·m at the listed 50 Hz point. It is not a direct replacement for the two-pole motor if the driven machine must retain its original speed.
A supply-frequency change also changes the machine speedThe YY90S2 speed columns differ by about 20.7%, and the YY90L4 columns by about 21.4%. Those percentages compare the catalogue speed entries; they are not permission to reconnect an existing winding at another frequency. Specify the actual voltage and frequency together, and obtain the rating and run-capacitor details for that supply.

Running power does not establish starting capability

Both 1.5 kW entries list starting torque / rated torque = 0.3, maximum torque / rated torque = 1.7 and starting current / rated current = 4.2. These ratios describe different operating conditions.

Check torque at zero speed first

Applying the 0.3 ratio to the calculated 50 Hz rated torques gives approximately 1.53 N·m for YY90S2 and 3.07 N·m for YY90L4. A load requiring more breakaway torque cannot be judged suitable simply because its running demand is below 1.5 kW. The 1.7 maximum-torque ratio is not the available starting torque.

Check the complete acceleration, not just the first movement

Provide the driven load’s torque-versus-speed behaviour, inertia and whether it starts unloaded. Ask for the selected winding’s torque curve and permitted starting duty. The catalogue ratios alone do not give acceleration time, allowable starts per hour or thermal recovery time.

Confirm the capacitor-run circuit as a complete assembly

Request the run-capacitor capacitance, voltage rating, wiring diagram and reversal arrangement for the ordered winding. Include photographs of the existing nameplate, capacitor and terminal markings for a replacement. This YY table does not supply those circuit details, and they cannot be borrowed from an AIRE2 or YL two-capacitor motor.

CATALOGUE OVERVIEW

About this motor series

Dafeng’s IEC single-phase catalogue includes a YY capacitor-run table with outputs from 0.025 to 2.2 kW. It lists 110/220 V, 50/60 Hz and separate running-speed columns for each frequency. Two- and four-pole versions have different output and starting-torque entries; for example YY90L2 is listed at 2.2 kW and 2800 rpm at 50 Hz.

This rating table applies to the YY capacitor-run subfamily, not every YL or YLD product shown in the same category. Starting-torque ratios are relatively low in several rows, so supply the starting load and capacitor requirements when requesting a quote. One table cell has an apparent decimal error; use a confirmed model datasheet before design approval.

Model / series reference: YY

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.025–2.2 kW
Voltage
110 / 220 V
Product Type
IEC single-phase induction motor
Example YY90L2
2.2 kW; 2800 rpm at 50 Hz
Supply Options
110 / 220 V
Catalogue Scope
Manufacturer model or series
YY Output Range
0.025–2.2 kW
Frequency Options
50 / 60 Hz
Detailed Subfamily
YY capacitor-run
Speed
Model dependent
Manufacturer
Dafeng Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail