48CZ1 NEMA48CZ 90 V DC motor

Manufacturer catalogue image · Series illustration

DC motors

48CZ1 NEMA48CZ 90 V DC motor

Power
0.1864 kW
Voltage
90 V DC
Frame
NEMA48CZ
Output
1/4 HP (approximately 0.186 kW)

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

48CZ1 replacement: preserve the inch shaft and UNC mounting

This 90 V armature motor combines a 5/8-inch shaft with 1/4-20 UNC flange threads. A nearby metric bore or bolt size is not an interchangeable fit. Use the original inch dimensions for the coupling and mounting, and treat the metric values below as conversions for comparison.

Keep the drawing letters with each converted dimension

Catalogue dimensions are in inches. Metric equivalents below are arithmetic conversions, not new manufacturing tolerances or a substitute for the original drawing.

Drawing detailOriginal inch valueMetric comparison
U — shaft diameter 0.625 in 15.875 mm
AH — shaft projection 2.19 in 55.626 mm
AJ — mounting circle 3.75 in 95.25 mm
AK — register diameter 2.5 in 63.50 mm
BD — flange diameter 4.25 in 107.95 mm
C — overall length 9.32 in 236.728 mm
Square key section 3/16 in 4.7625 mm
Key length 1-3/8 in 34.925 mm

Three checks that prevent a near-match replacement

Use UNC fasteners and the actual shaft fit

The face drawing calls out four 1/4-20 UNC-2B holes; the dimension table also specifies 1/4-20 UNC. This is not an M6 thread. Likewise, a nominal 16 mm coupling is not the same specified bore as 15.875 mm. Match the coupling fit, square key and flange register to the shaft and mounting drawing before ordering an adaptor.

90 V is the armature rating, not an AC input specification

The electrical row states 90 V armature, 2.8 A, 2,300 rpm and 1/4 HP. Select a compatible DC drive from those motor-side requirements and the real load; the table does not identify the drive’s incoming AC voltage or provide a starting-current rating. The 7 lb-in catalogue torque converts to about 0.791 Nm. That is a torque unit conversion, not a new overload rating.

Allow for TENV cooling and the lead exit

The enclosure is listed TENV, and the drawing shows leads leaving near the rear of the body with a 30-inch length note. Keep cable bend and service space beyond the 9.32-inch overall motor length. The catalogue does not specify a continuous-duty thermal limit at reduced speed; include operating speed, load cycle and ambient temperature when confirming the motor/drive combination. Do not infer IP sealing or fan-cooled performance from TENV.

CATALOGUE OVERVIEW

About this motor series

Eson's NEMA48C product page identifies the 48CZ1 model as a 90 V direct-current motor with a 1/4 HP output, 2300 rpm rated speed and 2.8 A current. Its table specifies a NEMA48CZ frame and TENV enclosure, with 7 lb-in torque and an approximate weight of 12 lb. The dimensional chart lists a 0.625-inch shaft diameter and uses inch dimensions throughout. The power shown in kilowatts is a conversion of the stated mechanical horsepower, not a separate manufacturer rating. For a replacement, compare the flange, shaft projection and threaded mounting details as well as the nominal frame label. Provide the controller and load requirements and confirm the intended duty and thermal conditions before selecting this motor for continuous operation.

Model / series reference: 48CZ1

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.1864 kW
Voltage
90 V DC
Frame
NEMA48CZ
Output
1/4 HP (approximately 0.186 kW)
Torque
7 lb-in
Enclosure
TENV
Rated Speed
2300 rpm
Rated Current
2.8 A
Shaft Diameter
0.625 inch
Approximate Weight
12 lb
Speed
Model dependent

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail