IEC71-B14 1/3 HP DC motor family

Manufacturer catalogue image · Series illustration

DC motors

IEC71-B14 1/3 HP DC motor family

Power
0.2486 kW
Voltage
90 or 180 V DC
Output
1/3 HP (approximately 0.249 kW)
Current
3.6 A at 90 V; 1.8 A at 180 V

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

IEC71/B14: four one-third-horsepower motors, two distinct speed choices

The 90 V and 180 V windings are offered at either 1,800 or 3,000 rpm. All four share the listed shaft and flange dimensions, but the faster version has lower rated torque, a shorter body and lower mass. Select speed and armature voltage separately before treating this as a mechanical replacement.

Choose a complete model, not just IEC71/B14 and 1/3 HP

Every row is listed at 1/3 HP, approximately 0.249 kW by mechanical-horsepower conversion. Current is the stated motor current; armature voltage is not the drive’s incoming AC supply.

ModelArmature voltageRated speedCurrentRated torqueLength C / mass
D7139018N 90 V 1,800 rpm 3.6 A 1.3 Nm 262 mm / 6.6 kg
D7131818N 180 V 1,800 rpm 1.8 A 1.3 Nm 262 mm / 6.6 kg
D7139030N 90 V 3,000 rpm 3.6 A 0.79 Nm 227 mm / 4.5 kg
D7131830N 180 V 3,000 rpm 1.8 A 0.79 Nm 227 mm / 4.5 kg

A matching flange does not preserve the machine duty

The faster motor trades torque for speed

The 3,000 rpm versions are 35 mm shorter, but their listed torque is 0.79 Nm instead of 1.3 Nm. On the same transmission ratio the output speed changes as well. If a machine needs the original low-speed torque, do not select the shorter version solely because it fits the available space; check the motor duty and transmission together.

Doubling armature voltage halves the listed current, not the power

At either speed, the 180 V version lists 1.8 A while the 90 V version lists 3.6 A, with the same rated output and torque for that speed. This is a winding/supply choice, not evidence of a 50% energy saving. Match the DC drive’s output-voltage capability, current rating and load requirements to the chosen model. Starting and overload currents are not specified by these rated values.

The shared interface is metric

All four dimensional rows give a 14 mm shaft diameter U, 30 mm projection AH, 70 mm register AK, 85 mm mounting circle AJ and M6 mounting threads BF. The body diameter O is 98 mm and the flange diameter BD is 101.6 mm. Compare these individually with the mating gearbox or coupling; 98 mm is the body diameter, not the mounting-circle diameter.

Keep thermal duty and service space in the order

The shorter 227 mm body and lower 4.5 kg mass belong to the 3,000 rpm configuration; the 1,800 rpm versions are 262 mm and 6.6 kg. Include the actual operating-speed range, load cycle, enclosure conditions and lead-exit clearance when specifying a replacement. The posted rating and outline do not establish a low-speed continuous-duty limit or a complete drive wiring diagram.

CATALOGUE OVERVIEW

About this motor series

Eson's IEC71-B14 page provides four D713 model combinations at 1/3 HP, with either 90 or 180 V DC supply and either 1800 or 3000 rpm rated speed. The 1800 rpm variants are listed at 1.3 Nm and 6.6 kg, whereas the 3000 rpm variants are listed at 0.79 Nm and 4.5 kg. Rated current follows the selected voltage: 3.6 A for 90 V and 1.8 A for 180 V in this table. The mechanical drawing gives a 98 mm body diameter, 14 mm shaft and B14 mounting details. Choose the complete order code rather than combining the torque of one speed variant with the dimensions of another. Confirm controller compatibility, flange fit and the required operating duty with the manufacturer.

Model / series reference: D713 IEC71-B14

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.2486 kW
Voltage
90 or 180 V DC
Output
1/3 HP (approximately 0.249 kW)
Current
3.6 A at 90 V; 1.8 A at 180 V
Mounting
IEC71 / B14
Rated Torque
1.3 Nm at 1800 rpm; 0.79 Nm at 3000 rpm
Body Diameter
98 mm
Speed Options
1800 or 3000 rpm
Shaft Diameter
14 mm
Approximate Mass
6.6 kg at 1800 rpm; 4.5 kg at 3000 rpm
Speed
Model dependent

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail