YE3-90S-2 1.5kW three-phase induction motor

Manufacturer catalogue image · Series illustration

AC induction motors

YE3-90S-2 1.5kW three-phase induction motor

Power
1.5 kW
Voltage
380 / 400 V
Frequency
50 Hz
Listed Mass
23 kg

Single model reference · Confirm the offered mounting and winding.

Read the 90S-2P row before sizing the supply or replacing a motor

Wangpai’s 1.5 kW product page also contains full YE3 family tables. The relevant row is YE3-90S-2P: 50 Hz, 2895 r/min and 4.95 N·m rated torque. The family headline of 0.55–315 kW and the generic 3000 r/min option must not replace this model’s values.

The single-model values, with their meaning

Transcribed from the manufacturer’s YE3-90S-2P row. The two currents correspond to two different supply columns. Starting ratios are separate from continuous rated values.

ItemListed valueUse in an offer review
Rated output / frequency 1.5 kW / 50 Hz Match the load requirement and site frequency
Rated speed / torque 2895 r/min / 4.95 N·m Use the loaded speed, not the 3000 r/min family heading
Current at 380 V 3.2 A Compare with the offered 380 V connection
Current at 400 V 3.0 A Compare with the offered 400 V connection
Efficiency / power factor 84.2% / 0.84 Catalogue values for this row; request the test basis
Locked-rotor / rated current 7.6 A ratio, not a 7.6 A current rating
Listed motor mass 23 kg Check the weight of the actual mounting version

Resolve the three ambiguities this row cannot settle

A correct electrical row still needs the supplied winding, starting method and mechanical drawing to become a complete replacement specification.

Which supply and connection will be supplied?

The product title names 380 V while the series introduction says normal 400 V. Both current columns are present in the model table. State the actual line voltage and ask the quotation and nameplate to agree on the winding and terminal connection. Do not infer a star/delta arrangement from these two voltage headings.

Will the starter and load suit the starting duty?

The 7.6 locked-rotor current ratio describes a different condition from the listed running current. Give the driven equipment, starting load, starts per hour and starter or VFD arrangement. The row does not state an acceptable acceleration time for your machine, so the rated current alone cannot approve the start.

Will the 90S assembly physically fit?

The table identifies the frame and mass but does not establish a complete foot or flange installation. Attach the old nameplate and measured shaft, mounting pattern and available clearance. Ask for the offered assembly drawing and terminal-box position before treating it as a drop-in replacement.

CATALOGUE OVERVIEW

About this motor

Wangpai’s YE3-90S-2 is a 1.5 kW two-pole motor. The matching YE3-90S-2P row specifies 2895 rpm at 50 Hz, 4.95 Nm rated torque and 84.2% efficiency. Current is listed separately as 3.2 A at 380 V and 3.0 A at 400 V. The same page contains much larger YE3 models; their ratings are not assigned to this 90S entry.

Model / series reference: YE3-90S-2

Published specifications

The values below refer to this model; check the supply and mounting of the offered assembly.

Power
1.5 kW
Voltage
380 / 400 V
Frequency
50 Hz
Listed Mass
23 kg
Rated Speed
2895 rpm
Product Type
YE3-90S-2 1.5kW three-phase induction motor
Rated Torque
4.95 Nm
Catalogue Scope
Manufacturer model or series
Current At 380 V
3.2 A
Current At 400 V
3.0 A
Supplier-listed Efficiency
84.2%
Speed
Model dependent
Manufacturer
Wangpai Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail