M30GXR28ZYT47 DC planetary gearmotor

Manufacturer catalogue image · Series illustration

DC motors

M30GXR28ZYT47 DC planetary gearmotor

Voltage
12 / 24 V
Product Type
M30GXR28ZYT47 DC planetary gearmotor
Nominal Ratios
3.7–720; discrete options
Catalogue Scope
Manufacturer model or series

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

M30GXR28ZYT47: the 12 V and 24 V versions have different load points

The motor behind this miniature planetary gearbox is not specified by voltage alone. Mabuqi lists 28ZYT47-1242 for 12 V and 28ZYT47-2438 for 24 V, then gives a separate geared-output table for each. At the same ratio, the 24 V version runs more slowly but has a higher listed rated output torque. Choose the required speed and load together before selecting the winding.

What changes between the two motor windings?

28ZYT47-1242: 12 VBefore reduction, the motor row lists 2.5 W output, 3,500 r/min rated speed and 4,250 r/min no-load speed. Rated current is 0.32 A, no-load current 0.075 A and stall current 1.44 A. The stall current is 4.5 times the rated current by calculation; a source or controller sized only around no-load current will not represent the loaded operating requirement.
28ZYT47-2438: 24 VThe 24 V row lists 2.4 W output, 3,100 r/min rated and 3,800 r/min no-load speed, with 0.16 A rated, 0.037 A no-load and 0.7 A stall current. These are a distinct winding’s data, not permission to double the voltage on the 12 V motor. Agree current limiting and overload duration with the supplier; the table does not give an allowable stalled-on time.
Stall torque is not a holding-duty specificationThe bare-motor rows list stall torque separately from rated torque. A blocked shaft is therefore a separate condition, not a continuous operating point. For a mechanism that reaches a hard stop, specify the stop detection, current limit and reset behaviour. Do not use a mechanical stop as the normal means of controlling travel without an approved duty.

Compare the same ratio at both voltages

Each cell below keeps rated output speed and torque together from its own motor table. These are geared-output points; the 2.5 W or 2.4 W bare-motor rating should not be copied to the output shaft at every ratio.

Nominal ratio12 V: speed / torque24 V: speed / torqueReducer length L
3.7 944 r/min / 0.019 N·m 836 r/min / 0.021 N·m 31 mm
14 255 r/min / 0.062 N·m 226 r/min / 0.068 N·m 40.1 mm
100 35 r/min / 0.388 N·m 31 r/min / 0.424 N·m 49 mm
264 13 r/min / 0.857 N·m 12 r/min / 0.94 N·m 57.9 mm
720 4.9 r/min / 2.3 N·m 4.3 r/min / 2.5 N·m 57.9 mm

Finish the selection with end-stop duty and the shaft drawing

Use rated torque rather than the emergency-stop row

At ratio 720, both tables list 7.5 N·m in the emergency-stop torque row, while rated output is 2.3 N·m for 12 V and 2.5 N·m for 24 V. The 7.5 N·m entry does not establish repeated stall capability. Provide the peak load, number of starts and reversals, and stopping method for approval.

Choose the actual shaft option

The standard output shaft is 6 mm diameter by 20 mm projection, with a flat shown in the drawing. A 4 mm by 13 mm option is separately offered. The front register is 18 mm and the four M3 mounting holes are on a 24 mm bolt circle. Confirm the selected shaft and tolerances before specifying a coupling; the optional shaft is shorter as well as smaller.

Allow for motor length and rear terminals

The drawing shows a 30 mm gearbox diameter, a 27.8 mm motor diameter and 46.6 mm motor length behind reducer dimension L. Add clearance for the rear terminals and wiring, and account for the front shaft projection. The 31–57.9 mm reducer lengths in the ratio table are not total assembly lengths.

Make speed acceptance a loaded test

The two bare-motor no-load speeds exceed their rated speeds. Define the output speed tolerance at the actual load and at the available supply voltage, including cable drop or battery variation. If speed must remain constant as load changes, agree the required feedback/control arrangement rather than assuming the gearbox alone regulates it.

Order one documented ratio, not any number in a range

The sheet lists discrete ratios from 3.7 through 720. It groups efficiencies at 80%, 70%, 60% and 50% as reduction stages increase. Its note mentions a possible five-stage extension, but that note does not supply rated speed/torque rows for such an assembly. Use one of the documented combinations or obtain a separate approved specification for a custom extension.

CATALOGUE OVERVIEW

About this motor series

Mabuqi’s M30GXR28ZYT47 miniature DC gearmotor offers separate 12 V and 24 V motor variants. Before reduction, the 12 V motor is listed at 2.5 W and 3500 rpm; the 24 V motor at 2.4 W and 3100 rpm. The planetary gearbox has discrete ratios from 3.7 to 720. A 6 × 20 mm output shaft is standard, with a 4 × 13 mm option. The two motor variants have different output-speed tables, so voltage, winding and ratio must be selected together.

Model / series reference: M30GXR28ZYT47

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Voltage
12 / 24 V
Product Type
M30GXR28ZYT47 DC planetary gearmotor
Nominal Ratios
3.7–720; discrete options
Catalogue Scope
Manufacturer model or series
Optional Output Shaft
4 × 13 mm
Standard Output Shaft
6 × 20 mm
12 V Motor-side Rating
2.5 W; 3500 rpm
24 V Motor-side Rating
2.4 W; 3100 rpm
Power
Confirm configuration
Speed
Model dependent
Manufacturer
Mabuqi Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail