M38GXR miniature planetary gearbox

Manufacturer catalogue image · Series illustration

Motor parts & accessories

M38GXR miniature planetary gearbox

Product Type
Planetary gearbox
Body Diameter
38 mm
Catalogue Scope
Manufacturer model or series
Standard Output Shaft
8 mm; 6 mm option

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

M38GXR: match the input pinion to the ratio and the motor shaft

M38GXR is a 38 mm planetary gearbox component. Its source drawing assigns different input pinions to different ratio options, so an output-speed requirement alone is insufficient for ordering. The input gear, motor shaft bore and adapter geometry must be selected along with output torque and installation length.

The ratio determines which pinion family is shown

Both pinion families use module 0.5. The source marks the 4.0 mm bore as the standard maximum bore in the 17-tooth group; it also lists smaller bore choices. Confirm the exact shaft fit and pinion supplied with the ordered assembly.

Input pinionListed bore optionsAssociated nominal ratios
17 teeth 4.0, 3.5 or 3.175 mm 3.7, 14, 19, 51, 71, 100, 189, 264, 369, 516
11 teeth 3.0 mm 5.2, 27, 139, 720

Higher reduction changes torque capacity, loss and body length

Torque is published in kgf·cm. The approximate N·m values below are unit conversions using 1 kgf·cm = 0.0980665 N·m. The higher momentary-torque column is not the continuous rating.

Nominal ratiosPermitted output torqueMomentary limitEfficiencyBody length / mass
3.7, 5.2 3 kgf·cm ≈ 0.294 N·m 10 kgf·cm 80% 31.0 mm / 195 g
14, 19, 27 12 kgf·cm ≈ 1.177 N·m 36 kgf·cm 70% 40.1 mm / 210 g
51, 71, 100, 139 25 kgf·cm ≈ 2.452 N·m 75 kgf·cm 60% 49.0 mm / 290 g
189, 264, 369, 516, 720 30 kgf·cm ≈ 2.942 N·m 90 kgf·cm 50% 57.9 mm / 330 g

Check these interfaces on the assembly drawing

Output shaft and front mounting

The standard output is an 8 mm shaft with a flat, extending 20 mm, with a 22 mm locating register and four M3 mounting holes on a 28 mm bolt circle. A 6 mm output shaft is offered separately. The input pinion’s 3.0–4.0 mm bore choices refer to the motor shaft, not the reducer’s output shaft; specify both ends explicitly.

Motor-side location and pinion engagement

The input drawing shows a 25 mm interface diameter and separate 3.5 mm and 2.8 mm hole pairs, plus a motor connection plate and pinion arrangement. Some assembly dimensions are shown in parentheses for the 3.7 and 5.2 ratios. Obtain the drawing for the exact ratio and motor instead of applying the same pinion position to every option.

Use exact ratio in travel calculations

Nominal 14 is listed as 13.733, nominal 100 as 99.506 and nominal 720 as 720.989. For example, at an assumed 3,000 r/min input, the last ratio gives about 4.16 r/min output by calculation. This predicts geometric speed reduction, not motor torque availability or speed regulation under load.

Separate reversing accuracy from shaft clearance

The source specifies no-load, single-stage backlash of at most 3 degrees. It separately lists axial shaft play of at most 0.3 mm and radial play of at most 0.05 mm. These are different measures; the single-stage backlash value does not establish multi-stage loaded repeatability. Give the allowed lost motion at the driven mechanism and ask for the applicable ratio’s test result.

Approve load position and assembly force

The sheet lists radial load up to 8 kgf, axial load up to 3 kgf and maximum shaft press-fit force of 150 N. The load position and combined-load condition are not defined in that table. Provide overhang, mounting orientation and assembly method for approval rather than treating each standalone maximum as simultaneously available.

Complete the motor and environment selection

The sheet recommends motor input speed no higher than 10,000 r/min and lists −20 to 80 °C with 20–85% RH. These gearbox entries do not rate an attached motor or establish an ingress-protection level. Specify continuous input speed, reversals, required life and surroundings together with the selected metal or powder-metal gear option; the drawing does not provide a material-specific life guarantee.

CATALOGUE OVERVIEW

About this component series

Mabuqi’s M38GXR is a 38 mm planetary reducer supplied as a gearbox component. The table groups nominal ratios from 3.7 to 720 across increasing stage counts. Its standard output shaft is 8 mm, with a 6 mm option. Permitted output torque rises from 3 to 30 kgf·cm across the listed groups, while efficiency falls from 80% to 50%. Select the ratio group and motor-side pinion interface together; the sheet does not define the rating of an attached motor.

Model / series reference: M38GXR

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Product Type
Planetary gearbox
Body Diameter
38 mm
Catalogue Scope
Manufacturer model or series
Standard Output Shaft
8 mm; 6 mm option
Permitted Output Torque
3–30 kgf·cm; ratio-dependent
Nominal Reduction Ratios
3.7–720; discrete options
Recommended Maximum Motor Input Speed
10000 rpm
Manufacturer
Mabuqi Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail