M60GXR60BLY brushless planetary gearmotor

Manufacturer catalogue image · Series illustration

Brushless DC motors

M60GXR60BLY brushless planetary gearmotor

Voltage
24 / 310 V
Product Type
M60GXR60BLY brushless planetary gearmotor
Internal Drive
Not included
Nominal Ratios
3.6–326; discrete options

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

M60GXR60BLY: 120 W at the motor is not 120 W at every geared output

The official assembly sheet pairs a 60BLY87 brushless motor with a planetary reducer and publishes separate rated operating points after reduction. The motor is offered in 24 V and 310 V windings, with no internal drive. At high ratios the reducer’s 30 N·m listed rated-torque ceiling makes the actual output speed and torque more useful than the headline motor power.

Choose the electrical version before specifying the controller

60BLY87-2439: 24 V windingThe motor table lists 120 W output, 3,000 r/min rated speed, 3,900 r/min no-load speed, 6.67 A rated current and less than 0.8 A no-load current. Those are motor-side data. Size the driver and source for starting and the load cycle as well as rated operation; dividing 120 W by 24 V does not reproduce the listed input current.
60BLY87-31039: 310 V windingThe corresponding row lists the same 120 W, 3,000 r/min rated and 3,900 r/min no-load speed, but 0.48 A rated and less than 0.3 A no-load current. This is a different winding and drive requirement, not a software setting on the 24 V motor. Both rows state that an internal drive is absent; obtain the external controller and feedback/phase wiring specification with the assembly.

Selected rated output points from the two gearbox tables

The 24 V and 310 V tables give the same values below. Power in the last column is calculated as torque × speed × 2π/60 from those listed operating points; it is not a separate tested power rating or a guarantee across the speed range.

Nominal ratioListed rated speedListed rated torqueCalculated output power
3.6 808 r/min 0.94 N·m About 79.5 W
13 218 r/min 2.98 N·m About 68.0 W
65 30 r/min 12.8 N·m About 40.2 W
198 11.37 r/min 30.0 N·m About 35.7 W
326 4.6 r/min 30.0 N·m About 14.5 W

Which speed should go into the machine specification?

Separate no-load rotation from the rated load point

At ratio 326, the sheet lists 11.9 r/min no-load but 4.6 r/min rated output. At ratio 65 it lists 60 and 30 r/min respectively. A conveyor or feeder that must maintain speed under load should therefore be specified using its required torque and speed together, not the no-load number.

Ask for the basis of the rated-speed row

Several listed rated outputs do not equal the motor’s 3,000 r/min rating divided by nominal ratio. For example, 3,000/326 is about 9.2 r/min, whereas the table states 4.6 r/min. The public sheet does not explain that difference. Preserve the listed point when comparing offers and request the approved motor speed, load and control conditions for the chosen ratio rather than silently replacing the table with a calculation.

Do not use maximum permitted torque as continuous torque

The sheet separates rated torque from a maximum permitted torque row. For ratios 198 through 326 it lists 30 N·m rated and 90 N·m maximum permitted. The latter does not establish a continuous operating point or a repeatable acceleration duty. Provide overload magnitude, duration and frequency and obtain an explicit permitted duty from the supplier.

Specify the complete ratio, winding and installation envelope

Reducer stages change length and efficiency

The sheet groups nominal ratios 3.6–4.3, 13–18, 47–77 and 168–326 into one through four stages. Their reducer lengths L are 40.5, 51.8, 63.1 and 74.4 mm, with listed efficiencies of 80%, 70%, 60% and 50%. Use the discrete ratio and its stage row, not an arbitrary ratio anywhere inside the overall range.

Reserve the motor body and shaft projection too

The dimensioned drawing shows a 60 mm cylindrical body, an 87 mm motor length behind the reducer, a 12 mm keyed output shaft extending 28 mm and a 32 mm locating register. Four M5 output mounting holes are on a 45 mm bolt circle. Obtain the toleranced assembly drawing for the selected L value and leave room for the cable exit; reducer length alone is not the installation envelope.

Resolve the Hall and controller configuration

The Hall column in both motor rows is marked ‘Both’, while the internal-drive column says ‘No’. That wording does not identify the delivered Hall option, connector pinout or commutation sequence. Include the selected feedback arrangement, controller model, supply and required direction of rotation in the order, then verify them together before connecting the load.

CATALOGUE OVERVIEW

About this motor series

Mabuqi pairs its M60GXR planetary gearbox with a 60BLY87 brushless DC motor. The motor table separates 24 V and 310 V variants, both listed at 120 W shaft output and 3000 rpm before reduction. The gearbox table offers nominal ratios from 3.6 to 326, with rated output speed from 808 to 4.6 rpm and torque up to 30 Nm. The motor’s 120 W rating must not be treated as the post-gearbox output at every ratio.

Model / series reference: M60GXR60BLY

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Voltage
24 / 310 V
Product Type
M60GXR60BLY brushless planetary gearmotor
Internal Drive
Not included
Nominal Ratios
3.6–326; discrete options
Catalogue Scope
Manufacturer model or series
Motor Rated Speed
3000 rpm before reduction
Motor-side Output
120 W
Rated Gearbox Speed
4.6–808 rpm
Motor Supply Variants
24 / 310 V
Highest Listed Rated Gearbox Torque
30 Nm
Power
Confirm configuration
Speed
Model dependent
Manufacturer
Mabuqi Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail