NXK51 brushless through-flow blower motor

Manufacturer catalogue image · Series illustration

Brushless DC motors

NXK51 brushless through-flow blower motor

Frequency
50 / 60 Hz
Net Weight
1.95 kg
Product Type
NXK51 brushless through-flow blower motor
Catalogue Scope
Manufacturer model or series

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

Size the NXK51 around the pressure loss of the complete airflow path

The 1,000 W FX06 curve falls as airflow rises: 215 m³/h and 29.5 kPa are separate maxima, not one operating point. The useful selection question is whether the blower can supply your required flow through the filter, hose and nozzle at their combined pressure drop. The drive board also needs its own mounting and cooling space.

Start with the flow your application still needs through a loaded filter

Plot flow and pressure together

For the NXK51-1000-FX06 at the 1,000 W setting, the curve is near 29.5 kPa at the low-flow end and falls toward the high-flow end. At about 120 m³/h, the graph reads roughly 14–15 kPa; the 500 W FX06 curve is roughly 7–8 kPa at that flow. These are approximate readings from the plotted curves, not guaranteed test points. They show why selecting only by free-air flow can miss the pressure required by a restrictive system.

Compare the operating point at clean and loaded conditions

State the required flow and combined pressure drop of the nozzle, hose, filter and fittings. Include the expected loaded-filter condition as a second duty point. Compare those points against the appropriate FX06 power-setting curve or the separate FX05 curve. A system requiring more pressure than that curve provides at the desired flow cannot be justified by quoting the maximum vacuum at near-zero flow.

Use maximum input as an electrical limit, not useful output

The table reports maximum electrical input power. It does not report shaft output, air power efficiency or continuous operation at a blocked inlet. Ask for the permitted operating envelope and thermal behaviour of the chosen duty cycle; the endpoint of a performance curve is not an instruction to run there continuously.

Keep the FX05 and FX06 curve identities with the order

Catalogue maxima, each reached under its own test condition. All rows list 50/60 Hz and a 1.95 kg blower mass. The supply and driver wiring must match the chosen model.

Model / settingListed supplyMaximum inputMaximum airflowMaximum vacuum
NXK51-0800-FX05 120 V 800 W 192 m³/h 23.0 kPa
NXK51-1000-FX06, 500 W 230 V 500 W 172 m³/h 21.0 kPa
NXK51-1000-FX06, 800 W 230 V 800 W 202 m³/h 26.0 kPa
NXK51-1000-FX06, 1,000 W 230 V 1,000 W 215 m³/h 29.5 kPa

Package the blower and drive board as two separate assemblies

Blower airflow connectionThe outline shows a 130 mm outer diameter, a 31.8 mm inlet and a 115 mm axial dimension. Design the inlet adaptor and support from the full outline; the motor-side geometry and cable exit also require space. A pipe that fits the inlet still needs a pressure-loss check against the duty point above.
Drive board mountingThe separate controller drawing shows a 133 × 90 mm face and an 80 mm side envelope, with four 5 mm mounting holes on a 122.5 × 80 mm pattern. Reserve additional connector and wiring clearance. Those dimensions belong to the drive assembly, not to the 130 mm blower housing; combining them into one motor dimension would make the enclosure plan misleading.
Speed command and enclosure protectionThe product supports 0–10 V DC or PWM speed control. The controller drawing identifies command connections separately from the power and motor terminals. Confirm the PWM frequency, signal reference and pinout before connecting a machine controller. The blower is listed IP00 with class F insulation, so it needs the application’s protective enclosure and suitable airflow conditions; sealed ball bearings do not make the complete blower dustproof or waterproof.

CATALOGUE OVERVIEW

About this motor series

NEWTHINK’s NXK51 through-flow blower includes a 120 V, 800 W entry and 230 V configurations at 500, 800 and 1000 W maximum input. The 230 V, 1000 W row lists 215 m³/h maximum airflow, 29.5 kPa maximum vacuum and 45000 rpm maximum speed. Use the flow-pressure curve to choose an operating point rather than combining separate maximum values.

Published watts are maximum electrical input, not rated shaft output; they are not inserted into the output-power filter.

Model / series reference: NXK51

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Frequency
50 / 60 Hz
Net Weight
1.95 kg
Product Type
NXK51 brushless through-flow blower motor
Catalogue Scope
Manufacturer model or series
Maximum Input Power Options
500 / 800 / 1000 W
Power
Confirm configuration
Voltage
Confirm supply
Speed
Model dependent
Manufacturer
NEWTHINK Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail