NXK73 brushless bypass blower motor

Manufacturer catalogue image · Series illustration

Brushless DC motors

NXK73 brushless bypass blower motor

Frequency
50 / 60 Hz
Net Weight
2.55 kg
Product Type
NXK73 brushless bypass blower motor
Catalogue Scope
Manufacturer model or series

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

NXK73: the same 10 kPa headline can hide a different usable flow

NXK73C1200Z005 is listed in both 120 V and 230 V versions, but their pressure–flow curves separate substantially once flow increases. Match the supply-specific curve, then check the side outlet and five-position harness against the space and controller in your machine.

Choose the voltage version from the working part of the curve

A 210 m³/h requirement separates the versions

At approximately 210 m³/h, the 230 V NXK73C1200Z005 curve reads about 6.5 kPa, while the 120 V curve reads about 5 kPa. These are approximate graph readings, not guaranteed operating points. A design needing around 6 kPa at that flow therefore cannot treat the two versions as interchangeable merely because both list a 10 kPa maximum vacuum.

The 230 V listing has a higher input and airflow ceiling

The table lists NXK73C1200Z005 at 850 W maximum input and 276 m³/h maximum airflow for 120 V, versus 1,100 W and 300 m³/h for 230 V. Both rows list 15,000 rpm maximum speed and 2.55 kg mass. Keep the voltage and model suffix together in the inquiry; neither the common speed limit nor the common mass makes their curves identical.

FZ01 is a separate lower-power option

NXK73-0500-FZ01 is listed at 230 V, 550 W maximum input, 250 m³/h maximum airflow, 8 kPa maximum vacuum and 13,500 rpm. Its curve is below both C1200Z005 versions through much of the range. Use its own curve for a low-resistance duty instead of applying the 300 m³/h figure from the larger variant.

Keep the curve within its demonstrated range

The published lines stop above zero pressure; do not extend them to invent a free-air endpoint or extrapolate a blocked-flow duty allowance. Provide the required flow together with the pressure drop of the installed air path and filter. The catalogue watts are maximum input, not guaranteed air power or continuous shaft output.

Resolve the side outlet and control harness before freezing the enclosure

The side outlet determines the duct layoutThe drawing shows a 192.2 mm overall front-view width, 188 mm height and 147.2 ±0.5 mm axial dimension, with a 144.4 mm motor-body diameter. The outlet’s E-view is a shaped flange with its own 50 mm dimension and 4 mm hole callout. Use that section to design the mating duct; treating the blower as only a round 7.3-inch package omits the outlet projection.
The harness contains power and a low-level commandThe five-position drawing labels 1 as blue DC−, 2 as red DC+ for the 0–10 V speed command, 3 as yellow/green ETH, 4 as black AC N and 5 as white AC L. Confirm the connector orientation and selected variant’s wiring before assembly. The 0–10 V pair is the command interface, not the main supply. Although PWM is advertised too, this drawing does not establish its connection or frequency specification.
Protect the installed assemblyThe product is listed IP20, class F and fitted with sealed ball bearings. Select enclosure protection and ventilation for the real environment; those bearing seals do not make the complete blower suitable for water spray. Keep cable routing and the airflow openings clear when checking the package, and obtain the chosen variant’s thermal and duty limits for sustained suction.

CATALOGUE OVERVIEW

About this motor series

NEWTHINK’s NXK73 bypass blower table lists configurations at 550, 850 and 1100 W maximum input. The 230 V, 550 W row specifies 250 m³/h maximum airflow and 8 kPa maximum vacuum; the 230 V, 1100 W row specifies 300 m³/h and 10 kPa. These are blower-system input figures rather than shaft-output ratings for a bare motor.

Published watts are maximum electrical input, not rated shaft output; they are not inserted into the output-power filter.

Model / series reference: NXK73

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Frequency
50 / 60 Hz
Net Weight
2.55 kg
Product Type
NXK73 brushless bypass blower motor
Catalogue Scope
Manufacturer model or series
Maximum Input Power Options
550 / 850 / 1100 W
Power
Confirm configuration
Voltage
Confirm supply
Speed
Model dependent
Manufacturer
NEWTHINK Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail