NXK57B brushless bypass blower motor

Manufacturer catalogue image · Series illustration

Brushless DC motors

NXK57B brushless bypass blower motor

Frequency
50 / 60 Hz
Net Weight
2.50 kg
Product Type
NXK57B brushless bypass blower motor
Catalogue Scope
Manufacturer model or series

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

An NXK57B replacement needs the full suffix and its own harness drawing

Two NXK57B configurations are listed at 600 W, but one is a 230 V B24 and the other a 120 V B21. The connector drawing also assigns mains and speed-command pins differently from other blowers in the same manufacturer’s range. Identify the exact version before retaining a power cable or controller.

Resolve the suffix and airflow units on the purchase specification

600 W does not uniquely identify the replacement

NXK57Z0600B24 is listed at 230 V with maxima of 170 m³/h, 11 kPa and 14,000 rpm. The 120 V NXK57Z1200B21 also lists 600 W maximum input, but its corresponding values are 176 m³/h, 12 kPa and 11,000 rpm. Keep the full suffix and voltage with the required duty; matching the watts alone does not match the supply or speed.

212 m³/h is about 124.8 CFM, not 212 CFM

The 230 V B21 row lists 1,000 W maximum input, 212 m³/h maximum airflow and 20 kPa maximum vacuum. The table’s equivalent airflow is 124.8 CFM. Record the unit explicitly when comparing a replacement: confusing 212 m³/h with 212 CFM would substantially overstate the available airflow.

The 230 V B21 pressure curve is distinct

At approximately 100 m³/h, its plotted pressure is around 13 kPa, versus roughly 7–8 kPa for the two 600 W curves. These are approximate graphical readings, not guaranteed duty points. State your required flow and system pressure loss together, and use that particular curve; the maximum vacuum and maximum flow are not a simultaneous performance promise.

Five positions do not mean a universal five-pin connection

Labels transcribed from the NXK57B outline. Confirm the connector viewing direction and supplied variant before wiring. Do not substitute the pin order from the NXK73 drawing.

PositionNXK57B drawing labelFunction shown
1 AC L Main supply line
2 AC N Main supply neutral
3 ETH Earth connection label
4 DC+ 0–10 V speed-command positive
5 DC− 0–10 V speed-command reference

Check the duct joint and enclosure around the actual outline

Side outlet and overall envelopeThe drawing gives an overall axial dimension of 157.8 mm, a 147.9 mm height callout at the motor end, and 144.4/144.8 mm body-diameter callouts at different sections. The side outlet has 40.0 and 44.5 mm diameter callouts. Match the hose or adaptor to the correct inner/outer mating surface and leave room for the bend; nominal 5.7-inch size does not specify that joint.
Mounting pattern and command specificationThe front view shows four 4.3 mm holes with separate 165.1 and 162.6 mm diameter callouts and angular details. Use the complete drawing to place them; it is not a simple pattern to infer from casing diameter. The product advertises PWM as well as 0–10 V, but the shown pin diagram only identifies the 0–10 V pair. Obtain the PWM interface requirements if that is the intended control method.
IP20 is not a liquid-ingestion specificationThe blower is listed IP20 with class F insulation and sealed ball bearings. Specify the process-air contamination, temperature and intended operating cycle. The bypass name and bearing seals do not by themselves establish approval for liquid ingestion, explosive atmospheres or sustained blocked-inlet operation.

CATALOGUE OVERVIEW

About this motor series

NEWTHINK’s NXK57B bypass blower table includes 600 W and 1000 W maximum-input configurations. The 230 V, 600 W entry lists 170 m³/h maximum airflow and 11 kPa maximum vacuum; a 230 V, 1000 W row lists 212 m³/h and 20 kPa. The model and performance-curve selection matter more than choosing the largest headline value.

Published watts are maximum electrical input, not rated shaft output; they are not inserted into the output-power filter.

Model / series reference: NXK57B

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Frequency
50 / 60 Hz
Net Weight
2.50 kg
Product Type
NXK57B brushless bypass blower motor
Catalogue Scope
Manufacturer model or series
Maximum Input Power Options
600 / 1000 W
Power
Confirm configuration
Voltage
Confirm supply
Speed
Model dependent
Manufacturer
NEWTHINK Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail