TZL28-0.75kW parking-system gearmotor

Manufacturer catalogue image · Series illustration

Geared motors

TZL28-0.75kW parking-system gearmotor

Power
0.75 kW
Voltage
380 V
Frequency
50 Hz
Brake Supply
DC 90 V

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

TZL28-0.75 kW: coordinate travel speed with brake release

The compact TZL28 is a 0.75 kW parking-mechanism gearmotor with six reductions. Its brake timing is much shorter than a complete machine stopping or positioning cycle, so the motor, brake supply and travel controller need to be specified together. Start with the required mechanism speed and its shaft interface.

Choose among six speed-and-torque pairs

Output torque is reproduced in the manufacturer’s kg-m notation. Each pair belongs to one listed ratio; a slow-ratio torque must not be paired with the fastest output speed.

1:30 and 1:40 — faster output optionsThe 1:30 row lists 50 rpm with 13.1 kg-m, while 1:40 lists 33.8 rpm with 19.4 kg-m. Use the actual sprocket or driven mechanism geometry to translate rpm into travel speed. The higher rpm choice has the lower listed output torque.
1:50 and 1:60 — intermediate reductionsThe 1:50 row lists 27.1 rpm and 24.1 kg-m; 1:60 lists 22.2 rpm and 29.5 kg-m. Specify the ratio itself in the order rather than only requesting the 0.75 kW motor, since the motor rating is shared across these options.
1:70 and 1:90 — lower speed, higher output torqueThe 1:70 row lists 20 rpm and 32.7 kg-m; 1:90 lists 15.8 rpm and 41.7 kg-m. The sheet’s separate 400 kg load entry does not specify the transmission geometry or complete machine mass. It is not a universal vehicle-weight or platform-capacity guarantee.

Put these details into the mechanism drawing and control sequence

Brake release and motor power are separate functions

The motor is rated 380 V, three phase, 50 Hz and 1.8 A. The brake coil is DC 90 V, supplied through the listed AC 200–240 V rectifier input. Obtain the actual brake switching diagram and coordinate release with motor operation; the coil supply cannot be inferred from the motor terminals.

0.02 s release is not a complete positioning specification

The DC-switch brake table gives 0.02 s release time, 0.07 s braking time and 1.5 kg-m brake torque. These values describe the brake, not the stopping distance or position accuracy of a platform with transmission backlash and load inertia. The stated operating frequency is 10 times per minute. Confirm the intended repeated cycle with the complete mechanism.

The compact gearbox has a defined shaft height

The drawing places the output-shaft centre 116 mm above the base. It gives a 28 mm h6 shaft, 45 mm extension and an 8 mm key-width callout, with an M8 ×20, pitch 1.25 end-thread callout. Overall length is 375.5 mm. Check coupling engagement and alignment against these dimensions instead of matching only shaft diameter.

Keep access to the base and brake adjustment

Four 12 mm mounting holes are shown on 90 mm longitudinal and 140 mm transverse spacing. The brake table gives a 0.3 mm specified air gap and 0.7 mm boundary value. Provide the necessary fastening and maintenance access in the installed layout; do not bury the adjustment area simply because the motor body fits.

Confirm loaded output speed for a timed movement

The motor row lists 1,400 rpm, whereas the listed 1:30 output is 50 rpm rather than an exact 1,400/30 result. The catalogue pairs remain useful for selecting a reduction, but a timed or synchronized mechanism needs the confirmed output speed under its actual load. Do not replace the published values with an assumed common input speed.

CATALOGUE OVERVIEW

About this motor series

Zhibao’s TZL28 parking-system gearmotor uses a 0.75 kW, four-pole, 380 V motor rated at 1400 rpm and 50 Hz. The ratio table runs from 1:30 to 1:90, with output speeds of 50–15.8 rpm. The dimension drawing identifies a 28 mm h6 output shaft and 375.5 mm overall length. The brake uses DC 90 V. Select the ratio and brake arrangement against the actual parking mechanism rather than comparing motor power alone.

Model / series reference: TZL28

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.75 kW
Voltage
380 V
Frequency
50 Hz
Brake Supply
DC 90 V
Motor Output
0.75 kW
Output Shaft
28 mm h6
Output Speed
15.8–50 rpm
Product Type
TZL28-0.75kW parking-system gearmotor
Catalogue Scope
Manufacturer model or series
Reduction Ratios
1:30 / 40 / 50 / 60 / 70 / 90
Motor Rated Speed
1400 rpm
Speed
Model dependent
Manufacturer
Shanghai Zhibao

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail