TZL50-2.2kW parking-system gearmotor

Manufacturer catalogue image · Series illustration

Geared motors

TZL50-2.2kW parking-system gearmotor

Power
2.2 kW
Voltage
380 V
Frequency
50 Hz
Brake Supply
DC 90 V

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

TZL50-2.2 kW: select the reduction and brake circuit together

This parking-system drive combines a 380 V three-phase motor, five gearbox ratios and a separate DC brake circuit. Its output-speed table helps compare travel-speed options, while the brake table supplies timing and adjustment data that should remain separate from gearbox output torque.

The five reductions exchange output speed for torque

These are the paired entries in the manufacturer’s TZL50-2.2 kW sheet. The torque column uses the catalogue’s “kg-m” notation; it is a torque unit, not a vehicle-mass rating.

Reduction ratioListed output speedListed output torque (kg-m)
1:60 23.2 rpm 88
1:75 19.1 rpm 106
1:85 17.3 rpm 118
1:100 13.8 rpm 148
1:120 12.1 rpm 168

Keep the motor power supply separate from brake control

Two voltage circuits belong in the quotation

The motor row specifies three-phase 380 V, 50 Hz, 2.2 kW, 5.5 A and 1,400 rpm. The brake row specifies a DC 90 V coil and AC 200–240 V rectifier input. Include the rectifier and switching arrangement in the order; do not connect the brake coil as though it were another 380 V motor winding.

Use the brake’s own torque and timing entries

The brake table lists 3.3 kg-m torque, 0.12 s braking time and 0.11 s release time under its DC-switch heading. These are catalogue brake entries, distinct from the gearbox-output torque table. They are not a measured stopping distance for the complete parking mechanism. The load inertia, transmission and actual switching circuit must be checked as part of the machine.

Preserve the adjustment and cycling limits

The air-gap table gives 0.3 mm as the specified value and 0.7 mm as the boundary value; the operating-frequency entry is 10 times per minute. Include access for inspection and the intended cycle pattern in the installation review. Do not interpret that frequency entry alone as approval for an unlimited repeated lifting duty.

Check the output interface and the complete lifted system

Shaft, base and couplingThe drawing gives a 50 mm h6 output shaft, a 14 mm key-width callout and 75 mm shaft extension. It shows four 18 mm base holes, with 160 mm longitudinal and 230 mm transverse mounting spacing; overall length is 496 mm. Compare the actual sprocket or coupling, screw engagement and base drawing before selecting the assembly.
Travel speed and lifting capacityUse the selected output rpm with the actual drum or sprocket geometry and transmission arrangement to establish travel speed. The sheet’s 1,800 kg output-load entry does not specify that geometry, reeving or the complete lifted mass. It therefore cannot be treated as a universal allowable vehicle weight. Provide the platform mass, transmission drawing and duty when requesting the matched drive.
Confirm the speed at the intended loaded conditionThe motor row lists 1,400 rpm, but the ratio table’s output speeds do not all equal exactly 1,400 divided by ratio. Retain the published pairs for initial comparison and ask for the selected ratio’s loaded output speed when synchronization or travel time is critical. Do not silently recalculate the table as though every entry were measured at the same motor speed.

CATALOGUE OVERVIEW

About this motor series

Zhibao’s TZL50 parking-system gearmotor pairs a 2.2 kW, four-pole motor with reduction ratios from 1:60 to 1:120. The 380 V, 50 Hz motor is rated at 1400 rpm, while the gearbox table gives output speeds from 23.2 to 12.1 rpm. Its drawing specifies a 50 mm h6 output shaft and 496 mm overall length. The integrated brake is a separate DC 90 V circuit; confirm the brake rectifier and mechanical interface as part of the assembly.

Model / series reference: TZL50

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
2.2 kW
Voltage
380 V
Frequency
50 Hz
Brake Supply
DC 90 V
Motor Output
2.2 kW
Output Shaft
50 mm h6
Output Speed
12.1–23.2 rpm
Product Type
TZL50-2.2kW parking-system gearmotor
Catalogue Scope
Manufacturer model or series
Reduction Ratios
1:60 / 75 / 85 / 100 / 120
Motor Rated Speed
1400 rpm
Speed
Model dependent
Manufacturer
Shanghai Zhibao

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail