Brushless DC motor range

Manufacturer catalogue image · Series illustration

Brushless DC motors

Brushless DC motor range

Power
0.1–0.75 kW
M077A-4116
300 V / 250 W / 3000 rpm
M077A-4119
24 V / 180 W / 1500 rpm
M077B-4465
24 V / 100 W / 1000 rpm

Catalogue series · Exact configuration and availability confirmed by the manufacturer.

M077 brushless selection: keep the winding suffix with the rated speed

The M077 catalogue contains different voltage and speed windings in similar-looking housings. Two verified 24 V, 200 W entries illustrate why the suffix must stay in the order: M077A-4440 is rated at 3,000 rpm, while M077A-4448 is rated at 2,500 rpm. Neither can be specified by “M077, 200 W” alone.

The same output power gives different torque at the rated point

M077A-4440: 24 V DC, 200 W, 3,000 rpmThe detailed product page specifies continuous duty. Calculating T = 9550 × 0.2 / 3000 gives about 0.637 Nm at that rated operating point. This is a calculation from the published output and speed, not an additional measured torque curve.
M077A-4448: 24 V DC, 200 W, 2,500 rpmThe corresponding calculation gives about 0.764 Nm, roughly 20% more rated-point torque at the lower speed. This does not establish the motor’s torque at zero speed or permission to increase controller current beyond its approved limit.
M077A-4435: resolve the voltage before orderingThe catalogue listing says 24 V, but its detailed page says 12 V for the same 200 W, 3,500 rpm designation. Treat the winding voltage as unresolved and request a revision-specific motor sheet. Do not choose the supply or controller from whichever of the two values is more convenient.

Use the linked D63B14 drawing as a configuration reference

The drawing is titled M077S D63B14, rather than either complete A-series winding code above. Confirm that the offered winding is supplied in this mechanical arrangement before using these dimensions.

Drawing featureReference value / action
Body and shaft 81.5 mm square body; 155 mm body length; 23 mm shaft extension; 11 mm shaft diameter; 4 mm key width.
Flange interface 75 mm fixing pitch circle, 60 mm locating register and four M6 tapped fixing holes shown on the drawing. Confirm tolerances and bolt engagement on the accepted revision.
Hall connector DJ7061Y-2.3-11; drawing identifies 5 V, ground and A/B/C signals. Obtain the mating view and matching controller connection sheet before wiring.
Electrical rating The mechanical drawing does not identify the full winding suffix or its rated current. Keep the drawing and electrical sheet together in the purchase specification.

Do not apply the shared family maxima to each winding

1.4 Nm and 4.2 Nm are family entries

The shared M077A/B table states maximum rated output torque of 1.4 Nm and peak torque of 4.2 Nm. It does not give the peak duration or current for each listed winding. Use the actual continuous operating point above and request a model-specific overload curve where the machine needs acceleration torque.

“Up to IP65” describes an option boundary

The same table states protection up to IP65, class F insulation and 120-degree Hall sensing. Confirm the delivered enclosure, connector sealing and feedback arrangement; an upper protection rating is not proof that every stock version includes it.

Choose the controller from electrical data, not output watts alone

A 200 W mechanical output is not a 200 W electrical-input requirement. The reviewed individual pages do not state efficiency or rated current, so dividing 200 W by 24 V would understate input current by ignoring losses. Request continuous and peak phase/current limits and the agreed commutation arrangement for the exact winding.

CATALOGUE OVERVIEW

About this motor series

AMOP’s brushless range publishes model-specific voltage, output and speed combinations. Examples include M077A-4116 at 300 V, 250 W and 3000 rpm; M077A-4119 at 24 V, 180 W and 1500 rpm; and M077B-4417N at 36 V, 750 W and 5000 rpm. Another entry, M077B-4465, is 24 V, 100 W and 1000 rpm. These combinations must be kept together when matching the motor to a controller.

The power filter reflects the reviewed models shown on this catalogue page, not the complete multi-page range.

Published specifications

Specifications describe a series range; confirm which ratings apply together to the quoted model.

Power
0.1–0.75 kW
M077A-4116
300 V / 250 W / 3000 rpm
M077A-4119
24 V / 180 W / 1500 rpm
M077B-4465
24 V / 100 W / 1000 rpm
M077B-4417N
36 V / 750 W / 5000 rpm
Product Type
Brushless DC motor range
Catalogue Scope
Product family / configuration confirmed on inquiry
Voltage
Confirm supply
Speed
Model dependent
Manufacturer
AMOP Motor

Confirm mounting and shaft dimensions against the drawing for the quoted configuration.

Share with your team

Keep your sourcing team on the same page.

LinkedInFacebookXWhatsAppEmail